manualshive.com logo in svg

Altera Cyclone IV, Device Handbook

Share
Download
Altera Cyclone IV Device Handbook Download Page 218

8–54

Chapter 8: Configuration and Remote System Upgrades in Cyclone IV Devices

Configuration

Cyclone IV Device Handbook,

May 2013

Altera Corporation

Volume 1

Figure 8–28. Combining JTAG and AS Configuration Schemes

Notes to 

Figure 8–28

:

(1) Connect these pull-up resistors to the V

CCIO

 supply of the bank in which the pin resides.

(2) Power up the V

CC

 of the EthernetBlaster, ByteBlaster II, or USB-Blaster cable with the 3.3-V supply.

(3) Pin 6 of the header is a V

IO

 reference voltage for the MasterBlaster output driver.The V

IO

 must match the V

CCA 

of the 

device. For this value, refer to the 

MasterBlaster Serial/USB Communications Cable User Guide

. When using the 

ByteBlasterMV download cable, this pin is a no connect. When using the USB-Blaster and ByteBlaster II cables, this 
pin is connected to 

nCE

 when it is used for AS programming, otherwise it is a no connect.

(4) The 

MSEL

 pin settings vary for different configuration voltage standards and POR time. To connect 

MSEL

 for AS 

configuration schemes, refer to 

Table 8–3 on page 8–8

, 

Table 8–4 on page 8–8

, and 

Table 8–5 on page 8–9

. Connect 

the 

MSEL

 pins directly to V

CCA

 or GND.

(5) Power up the V

CC

 of the EthernetBlaster, ByteBlaster II, USB-Blaster, or ByteBlasterMV cable with a 2.5-V V

CCA 

supply. 

Third-party programmers must switch to 2.5 V. Pin 4 of the header is a V

CC

 power supply for the MasterBlaster cable. 

The MasterBlaster cable can receive power from either 5.0- or 3.3-V circuit boards, DC power supply, or 5.0 V from 
the USB cable. For this value, refer to the 

MasterBlaster Serial/USB Communications Cable User Guide

.

(6) You must place the diodes and capacitors as close as possible to the Cyclone IV device. Altera recommends using 

the Schottky diode, which has a relatively lower forward diode voltage (VF) than the switching and Zener diodes, for 
effective voltage clamping. 

(7) These pins are dual-purpose I/O pins. The 

nCSO

 pin functions as 

FLASH_nCE

 pin in AP mode. The 

ASDO

 pin functions 

as 

DATA[1]

 pin in AP and FPP modes.

(8) Resistor value can vary from 1 k

 to 10 k

..

(9) Only Cyclone IV GX devices have an option to select 

CLKUSR

 (40 MHz maximum) as the external clock source for 

DCLK

.

DATA

DCLK

nCS

ASDI

Serial 

Configuration

De

v

ice

Cyclone I

V

 De

v

ice 

10 k

Ω

10 k

Ω

V

CCIO 

V

CCIO 

G

N

D

nCEO

nCE

nSTATUS
CO

N

F_DO

N

E

10 k

Ω

V

CCIO  

nCO

N

FIG

MSEL[ ]

(1)

(1)

(1)

(4)

10k

Ω

V

CCA

N

.C.

V

CCA

TCK

TDO

TMS

TDI

CLKUSR

(9)

G

N

D

V

CCA 

(5)

V

IO

 

(3)

3.3 

V

 

(2)

Pin 1

Pin 1

Download Cable

(JTAG Mode)

10-Pin Male Header 

(top view)

Download Cable

(AS Mode)

10-Pin Male Header

3.3 

V

10 pf

G

N

D

G

N

D

10 pf

10 pf

G

N

D

10 pf

G

N

D

(6)

(6)

(8)

(8)

3.3 

V

3.3 

V

3.3 

V

DATA[0]

DCLK

nCSO 

(7)

ASDO 

(7)

1 k

Ω

Summary of Contents for Cyclone IV











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands