manualshive.com logo in svg

Altera Cyclone IV, Device Handbook

The Altera Cyclone IV Device Handbook is a comprehensive manual detailing all the features and specifications of this powerful FPGA. Users can download the manual for free from manualshive.com to get a detailed understanding of how to use this versatile product in their projects.

Share
Download
background image

Chapter 6: I/O Features in Cyclone IV Devices

6–25

High-Speed I/O Interface

March 2016

Altera Corporation

Cyclone IV Device Handbook,

Volume 1

Table 6–6

 and 

Table 6–7

 summarize which I/O banks support these I/O standards in 

the Cyclone IV device family.

Table 6–6. Differential I/O Standards Supported in Cyclone IV E I/O Banks 

Differential I/O Standards

I/O Bank Location

External Resistor 

Network at Transmitter

Transmitter (TX)

Receiver (RX)

LVDS

1,2,5,6

Not Required

v

v

All

Three Resistors

RSDS

1,2,5,6

Not Required

v

—

3,4,7,8

Three Resistors

All

Single Resistor

mini-LVDS

1,2,5,6

Not Required

v

—

All

Three Resistors

PPDS

1,2,5,6

Not Required

v

—

All

Three Resistors

BLVDS 

(1)

All

Single Resistor

v

v

LVPECL 

(2)

All

—

—

v

Differential SSTL-2 

(3)

All

—

v

v

Differential SSTL-18 

(3)

All

—

v

v

Differential HSTL-18 

(3)

All

—

v

v

Differential HSTL-15 

(3)

All

—

v

v

Differential HSTL-12 

(3)

, 

(4)

All

—

v

v

Notes to 

Table 6–6

:

(1) Transmitter and Receiver f

MAX

 depend on system topology and performance requirement.

(2) The LVPECL I/O standard is only supported on dedicated clock input pins.

(3) The differential SSTL-2, SSTL-18, HSTL-18, HSTL-15, and HSTL-12 I/O standards are only supported on clock input pins and PLL output clock 

pins. PLL output clock pins do not support Class II interface type of differential SSTL-18, HSTL-18, HSTL-15, and HSTL-12 I/O standards.

(4) Differential HSTL-12 Class II is supported only in column I/O banks.

Summary of Contents for Cyclone IV











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone IV

Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
Rane CP 31 Datasheet preview
CP 31
Brand: Rane Pages: 4
Xilica Audio Design neutrino series Quick Start Manual preview
neutrino series
Brand: Xilica Audio Design Pages: 26
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
Matrox Millennium P650 User Manual preview
Millennium P650
Brand: Matrox Pages: 54
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
Medel RONDO 3 Quick Manual preview
RONDO 3
Brand: Medel Pages: 28
MF DIGITAL 5200 Live Series EventCD Operator'S Manual preview
5200 Live Series EventCD
Brand: MF DIGITAL Pages: 21
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Brand: S&T Pages: 28
Konica Minolta SRX-101A Operation Manual preview
SRX-101A
Brand: Konica Minolta Pages: 31
National Instruments IMAQTM User Manual preview
IMAQTM
Brand: National Instruments Pages: 121
Black Box Secure Site Manager 16 Quick Start Manual preview
Secure Site Manager 16
Brand: Black Box Pages: 16

Brands by name

Popular brands

Load more brands