allen XL5000 OPPOSITE Operating Instructions Manual Download Page 52

Page: 52 / 80

CLEANING AND MAINTENANCE

XL5000

M02001102EN0319

7.2.3

Inspection and replacement of the toothed belt

Carefully check the entire belt for damage, particularly for frayed reinforcement wires. If replacement of a toothed belt
is necessary, proceed as follows:

Step 1: Disconnecting the power supply

Switch the printing system off at the power supply switch and disconnect it from the power supply.

Step 2: Removing the cassette

Unlock the cassette by turning the cassette latch counterclockwise. Move the cassette out of the printer.

Step 3: Loosening the toothed belt

Loosen the toothed belt by loosening the fastening screw of the belt tensioner.

Step 4: Replacing the toothed belt

Remove the old belt and fit a new, undamaged toothed belt.

Step 5: Tighten toothed belt

Tighten the toothed belt and fix it by tightening the fastening screw of the belt tensioner.

Step 6: Inserting the cassette

Set the cassette into the printer. Lock the cassette by turning the cassette latch clockwise.

Step 7: Establishing the power supply

Connect the printing system to the power supply and switch on the printing system at the power supply switch.

7.2.4

Adjusting the ribbon tension

NOTE

Tools required to adjust tension:

▪

2.5 mm Allen wrench

▪

Roll of ribbon or ribbon cardboard core

–

42 mm diameter max.

▪

Spring scale with test band

Summary of Contents for XL5000 OPPOSITE

















































































Search results

Summary of Contents for XL5000 OPPOSITE

Reviews:

Related manuals for XL5000 OPPOSITE

Brands by name

Popular brands

allen XL5000 OPPOSITE, Operating Instructions Manual

Search results

Summary of Contents for XL5000 OPPOSITE

Reviews:

Related manuals for XL5000 OPPOSITE

Brands by name

Popular brands