allen XL5000 OPPOSITE Operating Instructions Manual Download Page 28 | Manualshive

Page: 28 / 80

background image

INSTALLATION

28

XL5000

M02001102EN0319

4

Installation

In the following chapter, you will find information on installation of the device.

CAUTION

Potential hazard due to incorrect or non-compliant installation!

An incorrect or improper assembly of the device may impair safety, functionality and efficiency of the de-
vice.

▪

The installation of the device may be performed exclusively by qualified technical expert personnel.

▪

Follow the relevant instructions in the operating manual.

4.1

Unpacking

CAUTION

Hazards due to defects or transport damage!

Transport damage to the device may result in unforeseeable hazards to personnel and/or property.

▪

When unpacking the device, check for any visible damage.

▪

Never ever connect a damaged device to the voltage supply.

▪

In case of transport damage, consult the manufacturer or your distributor.

NOTE

Check the deliverable items for completeness and condition.

After receipt of the shipment, please check immediately to see whether all items listed on the delivery
ticket are included and undamaged. The manufacturer does not accept liability for deficiencies that have
been claimed subsequently. File complaints with:

▪

Transport damages directly to the shipping service.

▪

Deficiencies and/or incompleteness immediately to the manufacturer or your distributor.

NOTE

Recycling of transport packing

The transport packaging may be stored for later recycling, e.g. transport or storage.

Step 1

: Open the transport packing.

Step 2:

Check whether all items listed on the delivery slip are included and undamaged.

Step 3

: Remove all components of the device carefully from the transport packing.

«
...
26
27
28
29
30
...
»

Summary of Contents for XL5000 OPPOSITE

















































































Reviews:

No comments

Related manuals for XL5000 OPPOSITE

Brand: Canon Pages: 300

Brand: Canon Pages: 288

Brand: MAKER MADE Pages: 21

Brand: Canon Pages: 58

Brand: Canon Pages: 30

Brand: TallyGenicom Pages: 38

Brand: Lexmark Pages: 59

Brand: Dascom Pages: 146

Brand: Olivetti Pages: 149

Brand: NBS Technologies Pages: 64

Brand: AstroJet Pages: 32

Brand: Novexx Solutions Pages: 6

Magicard Opera 100

Brand: Ultra electronics Pages: 2

Brand: 3nStar Pages: 44

Brand: Unisys Pages: 144

Brand: RAYSHAPE Pages: 41

Brand: Tally Pages: 14

Brand: Xerox Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands