allen XL5000 OPPOSITE Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 80

background image

PRODUCT SPECIFICATIONS

XL5000
M02001102EN0319

15

2

Product specifications

In this chapter, you will find information on deliverable items and equipment of the device.

2.1

Safety requirements

NOTE

Please always follow the safety instructions.

See “

Safety Information

” Chapter.

2.2

Deliverable items

NOTE

Check the deliverable items for completeness and condition.

After receipt of the shipment, please check immediately to see whether all items listed on the delivery
ticket are included and are undamaged. The manufacturer does not accept liability for deficiencies that
have been claimed subsequently. Complain against:

▪

Transport damages directly to the shipping service.

▪

Deficiencies and/or incompleteness immediately to the manufacturer or your distributor.

The following components belong to the standard deliverable items for the device:

Position

Qty

Part number

Description

1

1

103810-1

XL5000 Standard

–

EU

103810-2

XL5000 Opposite

–

EU

103810-3

XL5000 Standard

–

US

103810-4

XL5000 Opposite

–

US

103810-5

XL5000 Standard

–

CN

103810-6

XL5000 Opposite

–

CN

Including:

Qty

Part number

Description

1

-

Printing system

1

215341

Power supply

1

103806-1

power supply connection cable

–

EU

103806-2

power supply connection cable

–

US

103806-3

power supply connection cable

–

CN

1

-

Sample ribbon

1

103851

Kit accessories

Content:

Qty

Part number

Description

1

-

Serial cable (screened, male

–

fe-

male, 3 m)

1

-

Ethernet cable
(CAT 5E, 3 m)

1

-

I/O connection cable (screened,
3 m)

1

102687

Kit pneumatic service unit

1

103809

Kit wear and spare parts

1

-

Accessories USB pen drive

4

103804

Shim plate

«
...
13
14
15
16
17
...
»

Summary of Contents for XL5000 OPPOSITE

















































































Reviews:

No comments

Related manuals for XL5000 OPPOSITE

Brand: Lanier Pages: 150

Brand: Canon Pages: 31

Brand: Xerox Pages: 8

Brand: Oce Pages: 136

Brand: Oce Pages: 116

Brand: Canon Pages: 4

Brand: Oki Pages: 198

Brand: SEWOO Pages: 13

Brand: Magicard Pages: 124

Brand: Ricoh Pages: 44

Brand: Citizen Pages: 3

Brand: Axis Pages: 66

Brand: Axiohm Pages: 6

Brand: Lexmark Pages: 2

Brand: DNP Pages: 2

Brand: Magicard Pages: 31

Brand: SIGN RACER Pages: 73

Brand: UP Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands