allen XL5000 OPPOSITE Operating Instructions Manual Download Page 46 | Manualshive

Page: 46 / 80

background image

CLEANING AND MAINTENANCE

46

XL5000

M02001102EN0319

7.1

Cleaning

CAUTION

Hazards when working with technical cleaning towels

Incorrect handling of technical cleaning towels can entail a hazard for persons and/or property.

▪

Please observe the warning notices on the packaging of the technical cleaning towels.

ATTENTION

Damage to the equipment due to incorrect cleaning

The use of incorrect cleaning methods and the use of incorrect cleaning materials can damage the elec-
tronic and mechanical components of the equipment.

▪

Disconnect the equipment from the power supply before you begin cleaning.

▪

Observe the cleaning instructions described in the operating manual.

▪

Only use cleaning agents specified by the manufacturer.

ATTENTION

Maintenance for printhead

Good maintenance of the printhead is essential to ensure optimal print quality. It must be cleaned period-
ically depending on the working environment and print intensity setting.

▪

Do not use hard or abrasive material to clean the printhead.

NOTE

Cleaning the printing system

Regular cleaning prevents an accumulation of ribbon particles that can cause synchronization and print-
ing problems.

«
...
44
45
46
47
48
...
»

Summary of Contents for XL5000 OPPOSITE

















































































Reviews:

No comments

Related manuals for XL5000 OPPOSITE

Brand: Olivetti Pages: 438

da Vinci 1.0 Pro

Brand: XYZ Printing Pages: 11

Brand: Intamsys Pages: 5

Brand: iFactory3D Pages: 14

VarioPrint 6180

Brand: Oce Pages: 306

Brand: ICT Pages: 34

N2125N - DocuPrint B/W Laser Printer

Brand: Xerox Pages: 335

Brand: Epson Stylus Pages: 4

Brand: TransAct Pages: 45

Brand: Oki Pages: 2

Brand: Xerox Pages: 284

Brand: imagistics Pages: 2

Brand: Konica Minolta Pages: 102

Brand: Code Soft Pages: 101

Brand: Plas-Ties Pages: 18

Brand: Tachosys Pages: 5

Brand: Samsung Pages: 177

VORON BELT 350 KIT

Brand: ADITIVA 3D Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands