ADVANCED UV LIGHT Future Sun HP Owner'S Manual Download Page 71

Page: 71 / 73

Futuresun HP V2

Error Messages

Error code Possible causes and

correction

E001

Wind ﬂag does not switch on.
Check ﬂag switch and terminal.

E002

Filter glass defective or missing.
Replace ﬁlter glass.

E003

Sunbed acrylic lifted.
Position sunbed acrylic onto

sunbed.

E004

Front cover plate open.
Check if front cover plate ﬁts in

correctly.

E005

Emergency stop button activated.
Deactivate emergency stop

button.

E006

SunFresh-container empty
Reﬁll SunFresh container with

distilled water as described in

the chapter “Reﬁll of SunFresh

container”

E007

Condensation water container of

AC is full.
Empty the condensation water

container as described in the

chapter “Emptying condensation

water container”.

E008

Communication error.
Check supply cable/terminal to

control panel.

In order to delete an error message, push the button

“START/STOP”.

Then push the “+”-button for approx. 2 seconds.

You can now start a new tanning session.

Malfunctions during operation

Malfunction

Possible causes

and correction

The sunbed does not

start when time control

device is activated.

No electric supply.
Check fuses and FI

protective switch.

UV lamps are

ﬂickering.

Starter defective.
Replace starter.

The equipment is

running too hot.

Fresh a

ior supply and/or disposal

of exhaust air in the room

is insufﬁcient.
Control air vents and

remove from blockage if

necessary.

One or more UV

lamps in the top

canopy or sunbed do

not light up.

UV-lamps not correctly

installed into holders.
Instal UV-lamps correctly.

UV lamp defective.
Replace UV lamp.

One or more HID

lamps do not light up.

HID lamp(s) defective.
Replace HID lamp(s).

Ignitor for HID lamp

defective.
Replace ignitor.

Disposal

If the equipment is ﬁnally to be put out of service,

the equipment has to be properly disassembled.

When you dispose of the AC unit, the cooling

liquid has to be emptied, retrieved and disposed

of according to environmental standards.

All components need to be sorted and recycled.

Dispose of the sunbed and its components

in accordance with applicable environmental

standards.

Summary of Contents for Future Sun HP










































































Search results

Summary of Contents for Future Sun HP

Reviews:

Related manuals for Future Sun HP

Brands by name

Popular brands

ADVANCED UV LIGHT Future Sun HP, Owner'S Manual

Search results

Summary of Contents for Future Sun HP

Reviews:

Related manuals for Future Sun HP

Brands by name

Popular brands