ADVANCED UV LIGHT Future Sun HP Owner'S Manual Download Page 17

Page: 17 / 73

Futuresun HP V2

Transport by dolly



4 persons lift one box onto the dolly.



Move the box to the place of installation.



4 persons lift the the box off the dolly.



Use the same procedure to move all boxes to the

place of installation.

Installation of equipment

and electrical connection

DANGER CAUSED

BY INCORRECT

ASSEMBLY!

Improperly performed

installation and connection

jobs may result in severe

damages and fatal injuries.

Assembly and electrical

connection must be

performed by authorized

service technicians and

certiﬁed electricians only.

CAUTION – DAMAGE

TO COMPONENTS!

Do not kick against

components. Do not scratch

or damage the surfaces, i.e.

with assembly tools.

The equipment is delivered ﬁxed to a wooden pallet.

In order to lift the sunbed from the pallet, it must be

disassembled and moved to the place of installation.

For disassembly, transportation of single components

to the site of installation and the assembly minimum

four adult persons are required to perform these jobs.

For disassembly and assembly of the sunbed, you will

need the following tools:



Allan key , 6 mm



Philips screwdriver (small, medium and large

sizes)



Flathead screwdriver (small, medium and large

sizes)

Preparations at site of

installation

WARNING

HEAVY LOAD!

Carrying the heavy sunbed

components can result in

overstrain and health risks.

Always carry the big

components of the sunbed

with 4 persons.



Move the sunbed on the pallet to the site of

installation. Observe directions regarding transport,

starting with page 15.



For the time being, position sunbed in

such a way that there is still sufﬁcient

space for assembly jobs at the rear site.



Remove the ribbon band.



Take off the two upper boxes put on top of the big

box on the wooden pallet.



Remove the staples from the packing.



Remove the packing.



Remove padding material.



Open the top canopy and take out the exhaust air

stack.



Store air stack at a safe place .



Take out the box with accessories inside the

sunbed.



Store box with accessories at a safe place.

Summary of Contents for Future Sun HP










































































Search results

Summary of Contents for Future Sun HP

Reviews:

Related manuals for Future Sun HP

Brands by name

Popular brands

ADVANCED UV LIGHT Future Sun HP, Owner'S Manual

Search results

Summary of Contents for Future Sun HP

Reviews:

Related manuals for Future Sun HP

Brands by name

Popular brands