Acer Altos G530 Series User Manual Download Page 57

Page: 57 / 190

Install the hot-plug cage.

(1) Slide the cage into the chassis. The cage is locked to the chassis

with an audible click.

Connect the following cables to their corresponding connectors on
the SATA RAID backplane board, mainboard and adapter:

Important:

If a four-bay hot-plug SATA HDD cage is already

installed in the top HDD bay, you must block the J1 jumper. Set
pins 2 and 3 to short.

(1) Attach the SATA data cable to the SATA HDD connector on the

backplane board

(1)

, then connect the other end of the cable

to the SATA connector on the SATA RAID card.

Note:

SATA connectors on the controller are keyed. Make sure

the SATA data cables are properly connected to its corresponding
connectors on the SATA RAID card.

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands