Acer Altos G530 Series User Manual Download Page 14

Page: 14 / 190

1 System tour

Optional media storage

•

Hot-plug HDD cage

•

Supports up to four 80-pin Ultra320 SCSI hard disk drives

•

Supports up to four SATA 150/300 hard disk drives

•

Easy-swap HDD cage

•

Supports up to four 68-pin SCSI hard disk drives

•

Supports up to four SATA 150/300 hard disk drives

Note:

The main difference between a hot-plug HDD cage and an

easy-swap HDD cage is the presence of a backplane board on the
rear side of the hot-plug HDD cage

SCSI controller

•

Onboard SCSI: LSI

Logic 1020A Ultra320 SCSI controller

•

Dual channel SCSI, SCSI RAID host bus adapter (optional)

SATA controller

•

Onboard SATA: Intel 6300ESB ICH I/O controller supports dual
channel SATA 150 ports

•

Eight channel SATA RAID host bus adapter (optional)

RAID

•

Software RAID 0, 1 for onboard SATA ports

•

Software RAID 1 for onboard SCSI port

Networking

•

Intel 82541Pl Gigabit Ethernet controller

•

Marvell Yukon 88E8050 PCI Express Gigabit Ethernet controller

PCI I/O

•

Five PCI bus slots with three separate bus segments:

•

Two 32-bit/33 MHz PCI bus slots

•

Two 64-bit/66 MHz PCI-X bus slots

•

One x8 PCI Express bus slots (with x4 connectors)

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands