Acer Altos G530 Series User Manual Download Page 98

Page: 98 / 190

4 BIOS setup

IDE Configuration

The IDE Configuration submenu lets you define the parameter settings

related to the hard disk/s.

Parameter

Description

Option

Onboard P-ATA
Channels

When set to Both, the system can
support both Primary and Secondary
PATA Controllers.

When set to Disabled, it disables the
integrated PATA Controller.

When set to Primary, it enables support
for Primary PATA Controller.

When set to Secondary, it enables
support for Secondary PATA Controller.

Both

Disabled

Primary

Secondary

Onboard S-ATA
Channels

Enables or disables the integrated
SATA Controller.

Enabled

Disabled

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands