Acer Altos G530 Series User Manual Download Page 13

Page: 13 / 190

Features summary

Listed below are the system’s key features:

Processor

•

Single or Dual Intel

Xeon

™

processors with 1MB or 2MB L2 cache

and 800 MHz front system bus

•

Supports Intel

Hyper-Threading Technology

•

Supports Intel

EM64T (Extended Memory 64 technology)

Chipset

•

North bridge: Intel E7320 MCH (Memory Controller Hub)

•

South bridge: Intel 6300ESB ICH I/O controller

Memory

•

Supports up to four DIMM sockets for a maximum memory
capacity of 8 GB

•

Supports 512 MB, 1GB and 2GB DDR2-400 registered ECC memory
modules

•

Supports dual-channel memory bus

•

Supports memory sparing technology

•

Supports x4 SDDC (Single Device Data Correction)

Media storage

•

Three 5.25-inch device bays supports:

•

3.5-inch, 1.44 MB floppy drive

•

DVD-ROM, DVD-RW, DVD combo drive

•

DAT72 tape drive

•

AIT tape drive

•

LTO half-height tape drive

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands