Acer Altos G530 Series User Manual Download Page 110

Page: 110 / 190

4 BIOS setup

100

Onboard NIC 2
(Right)

Enables or disables the onboard NIC2
(10Base-T/ 100Base/ 1000 Base network
interface controller).

Enabled

Disabled

Onboard NIC2
ROM

Enables or disables the onboard NIC2 ROM.

Enabled

Disabled

Onboard SCSI

Enables or disables the onboard SCSI
ontroller.

Enabled

Disabled

Onboard SCSI
ROM

Enables or disables the onboard SCSI ROM.

Enabled

Disabled

Onboard SCSI
Mode

Select a SCSI mode. Different RAID options,
such as RAID 0, RAID 1 or expanded RAID
arrays, are offered in the integrated SCSI
controller.

IM/IME
(RAID1/ 1e)

IS (RAID 0)

Slot 5 Option
ROM

Enables or disables the PCI 32/33 slot.

Enabled

Disabled

Parameter

Description

Option

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands