Acer Altos G530 Series User Manual Download Page 146 | Manualshive

Page: 146 / 190

background image

5 Troubleshooting

136

Warning! EHCI controller
disabled. It requires 64bit data
support in the BIOS.

The EHCI controller is disabled because of
incorrect data structure. This condition
occurs if the USB host controller needs 64-
bit data structure while the USB is ported
with 32-bit data structure.

Miscellaneous BIOS messages

Keyboard Error

Error in the keyboard connection. Make
sure keyboard is connected properly.

Keyboard/Interface Error

Keyboard interface test failed.

PS2 Keyboard not found

PS2 keyboard was not detected.

PS2 Mouse not found

PS2 mouse was not detected.

Unlock Keyboard

PS2 keyboard is locked. To continue BIOS
POST, unlock the keyboard.

System Halted

Reset to reboot the system.

Not enough space in Runtime
area!!. SMBIOS data will not be
available.

The size of the SMBIOS data exceeds the
available SMBIOS runtime storage size.

Error message

Description

«
...
144
145
146
147
148
...
»

Summary of Contents for Altos G530 Series































































































































































































Reviews:

No comments

Related manuals for Altos G530 Series

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Solstice II SGH-A817

Brand: Samsung Pages: 199

Brand: Samsung Pages: 192

Brand: Samsung Pages: 193

Brand: Samsung Pages: 2

Brand: Fysic Pages: 60

Brand: i.safe MOBILE Pages: 72

Brand: Alcatel Pages: 73

Brand: Spice Pages: 26

Brand: Slider Pages: 27

Brand: VERTIS Pages: 23

StrongPhone WiFi

Brand: Evolveo Pages: 9

Brand: Ericsson Pages: 37

3rd Generation Wi-Fi Phone

Brand: EZLoop Pages: 82

T Mobile Z10 LTE

Brand: Blackberry Pages: 22

Brand: Zte Pages: 9

Brand: Zte Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands