Acer Altos G530 Series User Manual Download Page 124

Page: 124 / 190

4 BIOS setup

114

System Management

The System Management submenu displays specific system
information. The screen below is for your reference only, system
configuration may vary.

Assert NMI on
PERR

Enables or disables the PCI bus PERR
(parity error) support.

Note:

This parameter is disabled when

the NMI on SERR is disabled.

Enabled

Disabled

Resume on AC
Power Loss

Defines the mode of operation if a
power loss occurs.

When set to Stays Off, the system
remains off after power shutdown.

When set to Power On, the system will
turn on after power is restored.

Stays Off

Power On

Chassis Type

Indicates the chassis that controls the
speed of the system fan.

Other

Parameter

Description

Option

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands