Acer Altos G530 Series User Manual Download Page 159

Page: 159 / 190

149

RAID configuration

Caution!

Using the RAID configuration utility erases all data

previously saved in the hard drives. Make sure that you backup
important files before starting the configuration process.

SCSI RAID configuration utility

The SCSI RAID configuration utility allows you to change the default
RAID configuration, such as the system volume of your SCSI hard disk.

For detailed information on how to use the SCSI RAID configuration
utility, refer to “Appendix D: SCSI RAID configuration” on page 173.

SATA RAID configuration utility

The SATA RAID configuration utility allows you to change the default
RAID configuration, such as system volume of your SATA hard disk.

For detailed information on how to use the SCSI RAID configuration
utility, refer to “Appendix C: SATA RAID configuration” on page 167.

Summary of Contents for Altos G530 Series































































































































































































Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands

Acer Altos G530 Series, User Manual

Search results

Summary of Contents for Altos G530 Series

Reviews:

Related manuals for Altos G530 Series

Brands by name

Popular brands