ABB OmniCore V400XT Product Manual Download

Page: 244 / 466

Note/Illustration

Action

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

xx2300001842

Removing the power unit

Note/Illustration

Action

Disconnect all connectors from the unit
to be replaced.

xx2100000322

Remove the screws and pull the power
unit out from the two guiding pins on the
mounting plate.

CAUTION

Only the sheet metal on the power unit
can be used for holding.
Do not touch the connectors or the filter
on the power unit.

CAUTION

The weight of the power unit is 13 kg.
Use protective gloves when lifting this
unit.

CAUTION

The cabling is sensitive to mechanical
damage. Handle it with care to avoid
damage to the cabling or the connector,
avoid any kind of tilt or skew.

Continues on next page

244

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

5 Repair

5.2.10 Replacing the power unit

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands