ABB OmniCore V400XT Product Manual Download Page 413

Page: 413 / 466

LEDs

The illustration below shows the indication LEDs on the Ethernet switch.

xx1800000584

Status LED

Significance

Description

Startup sequence:

No color: Input voltage is outside specified voltage or internal fault
in the switch.

Green, solid: The switch is operational.

If the LED does not turn steady green, the status indicator LED can be
used to identify the following issues:

Status LED

Fault indication:

•

No color: If input voltage is within specified voltage limits and the
LED is not lit then replace the switch.

Shows the status of Ethernet links.

Ethernet LEDs

Green:

•

Off:10 Mbps data rate is selected.

•

On:100/1000 Mbps data rate is selected.

Yellow:

•

Flashing: The Ethernet is active on link.

•

Solid: A LAN link is established.

•

Off: A LAN link is

not

established.

Product manual - OmniCore V400XT

413

3HAC081697-001 Revision: A

7 Troubleshooting

7.3.10 Troubleshooting the Ethernet switch (DSQC1035)

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands