ABB OmniCore V400XT Product Manual Download

Page: 132 / 466

Note

Article number

Spare part

DSQC 609

3HAC14178-1

DSQC 609 power supply

DSQC 634

3HAC13398-2

DSQC 634 power supply

DSQC 609 and DSQC 634

3HAC082083-001

Harness PSU 24V

DSQC 609 and DSQC 634

3HAC082508-001

Harness PSU

3HAB7983-1

End clamp

Required tools and equipment

Note

Article number

Equipment

Content is defined in section

Standard toolkit for controller on
page 424

Standard toolkit

ESD protective wrist band

Required documents

Note

Article number

Document

3HAC082020-008

Circuit diagram - OmniCore
V400XT

Installing the optional power supply

Preparations

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Opening the door on page 182

Open the door.

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

xx2300001842

Continues on next page

132

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

3 Installation and commissioning

3.7.5 Installing the power supply optional device

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands