ABB OmniCore V400XT Product Manual Download Page 210

Page: 210 / 466

Required spare parts

Note

The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the OmniCore V400XT via myABB Business Portal,

www.abb.com/myABB

Note

Article number

Spare part

DSQC1039

3HAC060960-001

Connected Services-3G [3013-3]

3HAC028459-001

Magnetic roof antenna, 3G

DSQC1040

3HAC060962-001

Connected Services-WiFi [3013-2]

3HAC059424-001

Magnetic roof antenna, WiFi

DSQC1041

3HAC061701-001

Connected Services-Wired [3013-
1]

Required tools and equipment

Note

Article number

Equipment

Content is defined in section

Standard toolkit for controller on
page 424

Standard toolkit

ESD protective wrist band

Required documents

Note

Article number

Document

3HAC082020-008

Circuit diagram - OmniCore
V400XT

Removing the Connected Services gateway

Preparations

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Opening the door on page 182

Open the door.

Continues on next page

210

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

5 Repair

5.2.4 Replacing the 3G Connected Services gateway

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands