ABB OmniCore V400XT Product Manual Download Page 319

Page: 319 / 466

Refitting the LED indicator

Refitting the LED indicator

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

Insert the LED indicator into the cover
from outer side of the door and the screw
from inner side and screw them up.

xx1900001926

Insert the terminals (X1 & X2) of cables
into the lamp and secure with the screws.

Concluding procedure

Note/Illustration

Action

Closing the door on page 183

Close the door.

Perform the function tests to verify that
the safety features work properly, see

Function tests on page 171

Product manual - OmniCore V400XT

319

3HAC081697-001 Revision: A

5 Repair

5.3.6 Replacing the LED indicator

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands