ABB OmniCore V400XT Product Manual Download Page 287

Page: 287 / 466

Removing the manipulator signal connector

Preparations

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Opening the door on page 182

Open the door.

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

xx2300001842

Removing the manipulator signal connector

Note/Illustration

Action

Disconnect all connectors from the unit
to be replaced.

Remove cable ties and cable supports.

xx2100000827

Remove nuts and attachment screws.

Push the manipulator signal connector
out through the front panel.

Continues on next page

Product manual - OmniCore V400XT

287

3HAC081697-001 Revision: A

5 Repair

5.3.1 Replacing the manipulator signal connector (SMB)

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands