ABB OmniCore V400XT Product Manual Download Page 280

Page: 280 / 466

Refitting the air filter

Refitting the polymeric filter element

The procedure below details how to refit the polymeric filter element (option

3005-2

Moist dust filter

Note/Illustration

Action

xx2100002583

Insert the polymeric filter element to the
filter and secure with the metallic line.

Refitting the air filter

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Refit the air filter unit to the cabinet.

Concluding procedure

Note/Illustration

Action

Perform the function tests to verify that
the safety features work properly, see

Function tests on page 171

280

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

5 Repair

5.2.17 Replacing the air filter

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands