ABB OmniCore V400XT Product Manual Download Page 249

Page: 249 / 466

Note/Illustration

Action

xx2300001492

Remove the screws and pull the power
unit out from the two guiding pins on the
mounting plate.

CAUTION

Only the sheet metal on the power unit
can be used for holding.
Do not touch the connectors or the filter
on the power unit.

Refitting the power unit

Refitting the power unit

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

xx2300001842

Continues on next page

Product manual - OmniCore V400XT

249

3HAC081697-001 Revision: A

5 Repair

5.2.11 Replacing the HVLP power unit (DSQC3072)

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands