ABB OmniCore V400XT Product Manual Download Page 217

Page: 217 / 466

Note

Article number

Spare part

Harness A2.K4.X1 - K7.ETH2

3HAC085903-001

Ethernet harness

Harness Adapter - K7.X1

3HAC085904-001

24V Adapter harness

Required tools and equipment

Note

Article number

Equipment

Content is defined in section

Standard toolkit for controller on
page 424

Standard toolkit

ESD protective wrist band

Required documents

Note

Article number

Document

3HAC082020-008

Circuit diagram - OmniCore
V400XT

Removing the Connected Services gateway

Preparations

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Opening the door on page 182

Open the door.

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

xx2300001842

Continues on next page

Product manual - OmniCore V400XT

217

3HAC081697-001 Revision: A

5 Repair

5.2.5 Replacing the 4G Connected Services gateway

Continued

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands