ABB OmniCore V400XT Product Manual Download Page 164

Page: 164 / 466

4.3.2 Cleaning of the controller cabinet

Required equipment

Note

Equipment, etc.

ESD protected

Vacuum cleaner

Cleaning considerations

This section specifies some special considerations when cleaning the controller.

•

Always use ESD protection.

•

Always use cleaning equipment as specified above. Any other cleaning
equipment may shorten the life of paint work, rust inhibitors, signs, or labels.

•

Always make sure that all protective covers are fitted to the controller before
cleaning.

•

Never remove any covers or other protective devices when cleaning the
outside of the controller.

•

Never use compressed air or spray with a high pressure cleaner.

•

Never leave the door open when cleaning the exterior.

164

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

4 Maintenance

4.3.2 Cleaning of the controller cabinet

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands