ABB OmniCore V400XT Product Manual Download Page 160

Page: 160 / 466

4.2 Inspection activities

4.2.1 Inspection of controller

Inspecting the OmniCore V400XT controller

Note/illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 29

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 45

xx2300001842

Inspect connectors and cabling to make
sure they are securely fastened and
cabling not damaged.

Inspect the fans and ventilation holes to
make sure they are clean.

After inspection: Temporarily turn the
power supply on. Inspect the fans to
make sure they function correctly. Switch
the power off.

160

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

4 Maintenance

4.2.1 Inspection of controller

Summary of Contents for OmniCore V400XT


















































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands

ABB OmniCore V400XT, Product Manual

Search results

Summary of Contents for OmniCore V400XT

Reviews:

Related manuals for OmniCore V400XT

Brands by name

Popular brands