ABB IRB 920 Product Manual Download Page 636

Page: 636 / 1008

Note

Action

CAUTION

For robots with protection type Clean Room

Always cut the paint with a knife and grind the
paint edge when disassembling parts of the robot!
See

Cut the paint or surface on the robot before

replacing parts on page 118

xx2100001094

Remove the screws and washers.

Remove the motor from the transmission module.

Tip

Move the internal harness out of the way.

Remove the timing belt from the transmission
module.

Refitting the transmission module

Use these procedures to refit the transmission module.

Refitting the axis-4 motor sub-assembly to the transmission module

Note

Action

For robots with protection type Clean Room:

Clean the joints that have been opened and wipe
the parts free from particles with spirit on a lint
free. See

Cut the paint or surface on the robot

before replacing parts on page 118

Note

After all repair work, wipe the Clean Room robot
free from particles with spirit on a lint free cloth.

Continues on next page

636

Product manual - IRB 920

3HAC075721-001 Revision: C

5 Repair

5.6.10 Replacing the transmission module

Continued

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 920

Reviews:

Brands by name

Popular brands

ABB IRB 920, Product Manual

Search results

Summary of Contents for IRB 920

Reviews:

Brands by name

Popular brands