ABB IRB 920 Product Manual Download Page 117

Page: 117 / 1008

Note

Action

Check the o-ring grooves.

The grooves must be geometrically correct and
should be free of pores and contamination.

Lubricate the o-ring with grease.

Tighten the screws evenly while assembling.

Check that the o-ring is not squashed outside
the o-ring groove.

Make sure that no grease is left on the robot
surface.

Product manual - IRB 920

117

3HAC075721-001 Revision: C

5 Repair

5.2.3 Mounting instructions for sealings

Continued

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 920

Reviews:

Brands by name

Popular brands

ABB IRB 920, Product Manual

Search results

Summary of Contents for IRB 920

Reviews:

Brands by name

Popular brands