3Com 3C10402B Administrator'S Manual Download Page 92

Page: 92 / 582

HAPTER

4: S

YSTEM

AINTENANCE

To revert to a single-disk system:

Use

Table 21

to determine which disk is the mirrored disk.

Shut down the system (click

System Maintenance > Reboot/Shutdown >

Shutdown

Remove the mirrored disk drive:

Unlock the disk tray.

Unscrew the two retaining screws.

Remove the disk tray.

Disconnect the disk data cable from the mirrored disk drive.

Disconnect the power harness from the mirrored disk drive.

Unfasten the mirrored disk from the disk tray using the Phillips
screwdriver and the screws provided with the disk.

Reinsert the disk tray.

Screw in the two retaining screws and lock the disk tray in place.

Restart the system.

Use the NBX NetSet utility to remove the disk mirroring license from the
NBX NetSet utility:

Click

Licensing and Upgrades > Licenses.

Click

Remove License.

From the

Select License to Remove

drop-down list, select

Disk

Mirroring License

Click

Summary of Contents for 3C10402B







































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3C10402B

Reviews:

Related manuals for 3C10402B

Brands by name

Popular brands

3Com 3C10402B, Administrator'S Manual

Search results

Summary of Contents for 3C10402B

Reviews:

Related manuals for 3C10402B

Brands by name

Popular brands