3Com 3C10402B Administrator'S Manual Download Page 90

Page: 90 / 582

HAPTER

4: S

YSTEM

AINTENANCE

Install the second disk drive:

Unlock the disk tray.

Unscrew the two retaining screws.

Remove the disk tray.

Connect the IDE disk cable to the disk drive.

Connect the power harness to the disk drive.

Fasten the new disk to the disk tray using your Phillips screwdriver and
the screws provided with the disk.

Reinsert the disk tray.

Screw in the two retaining screws and lock the disk tray in place.

Restart the system.

Verify that the disks begin the mirroring process.

On the Call Processor front panel, check the four status lights under the
PWR and S1 labels. The status lights labeled 1, 2, and 3 (

Figure 3

) indicate

disk status.

Figure 3

Disk and Power Status Lights

Table 21

describes the possible states of the status lights.

Table 21

Disk Status Light States

Explanation

LED 1

LED 2

LED 3

PWR

Attempting to boot from disk 0 (zero)

Off

Attempting to boot from disk 1

Off

Boot process complete, system initializing

Flashing N/A

N/A

System is running

N/A

S
1

Summary of Contents for 3C10402B







































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3C10402B

Reviews:

Related manuals for 3C10402B

Brands by name

Popular brands

3Com 3C10402B, Administrator'S Manual

Search results

Summary of Contents for 3C10402B

Reviews:

Related manuals for 3C10402B

Brands by name

Popular brands