Zontes ZT350-GK 2022, Руководство по обслуживанию

Страница: 55 / 94

7-FRONT FORK COMPONENT
54
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1 1250205-023000 GB70.1 inner hexagonal M8×35 (environmental color) 4 20N·m
2 1094100-063000 ZT310T-M front wheel hollow shaft Φ20×243 1
4 1274300-007000 ZT350-GK ABS induction ring gear (60 teeth) 1
5 1100100-783000 ZT350-GK front brake disc plate(320×5.0) 1
6 1251100-117093 Non-standard inner hex bolt M8×25(color zinc) 5
22
～
24N·m
7 1250402-001091 GB12615φ3×10 5
8 1094100-037000 ZT250-R front wheel right fixed bushing 1
9 1184300-021000 ZT350 tire pressure sensor
（
M8 elbow/120°
）
1
10 ZT350-GK front spoke wheel 1
11 1230100-566000 120/70ZR17 CM-A1S 58W TL E4 1
PROCEDURE:
●
Tire and wheel component
Remove 2 bolts
⑴
on the left front shock absorber bottom barrel "b" with 6# inner hexagon socket. First hold
the front wheel, then remove the hollow shaft
⑵
with 17# inner hexagon socket, remove the left shaft sleeve
⑶
,
move the front wheel assembly and the disc brake disc protective cover
⑴
downward, and remove the disc brake
cover assembly and the front wheel assembly. Remove the two bolts
⑴
of the right front shock absorber bottom
barrel "a" and remove the right fixed shaft sleeve
⑻
.
●
Brake disc, ABS ring gear
Using 6# inner hexagon socket remove 5pcs bolts
⑹
,Protect the brake disc
⑸
around the rivet
⑺
with masking
paper or double-sided adhesive tape, and then grind the rivet
⑺
off the drum with a small grinder, then take off
the ABS ring gear
⑷
and the disc
⑸
.
●
Tire and wheel component
First unscrew the valve cap
②
and drain the air. Remove the tire
⑾
with a professional tire puller. When
pulling the tire, avoid the position of the tire pressure sensor. Remove bolt
⑥
with 2.5# inner hexagon socket,
remove tire pressure sensor
⑤
, remove nut
④
with 12# sleeve, and then remove air nozzle
③
.
CAUTION:
●
Use a suitable tool to support the motorcycle to prevent accidents caused by dumping during disassembly.
●
Take care when disassembling tires and rims to prevent damage to the material.
●
After replacing the tire, check for leaks and balance.
●
Unqualified tire repair fluid may corrode the rim and cause potential safety hazards.
●
It should not be used because the tire self replenishment may block the air hole of the tire pressure
monitoring sensor, resulting in inflation difficulty or tire pressure monitoring failure.
●
Maintenance items
Tires: regularly check whether the tires have cracks, cracks, air pressure, etc. If the tire has been worn to
the tread wear mark, the tire of the same specification and model must be replaced. Refer to the relevant
contents of the manual for details. Tires are not suitable for use in areas with low temperatures. When the
outdoor temperature is too low, it is recommended to store the vehicle in a place with high temperature or
indoors to prevent frost cracking. Normal temperature: 280kpa.
Rim: check the rim for deformation, cracks and other defects. Support the rim horizontally and rotate it
to check whether there is clamping stagnation, swing, etc.
Rim oil seal: TC φ42×φ28×7, Bearings: Dimensions φ42×φ20×12, madel: 6004-2rs. Axle: check
whether there is deformation and bending with a dial indicator.
Brake disc: After replacing the brake disc, the new brake disc should be operated for about 300
kilometers to fully run in order to achieve the best braking effect. Be careful to leave enough braking
distance during running-in.
Fig.8 FRONT FORK
COMPONENT
Front wheel component
3 1274300-008000 ZT350-GK front tire shaft sleeve
（
φ20×φ28×
15.5/shoulder φ34
）
1