Zontes ZT350-GK 2022, Руководство по обслуживанию

Страница: 14 / 94

2-FRAME & ENGINE COMBINATION 13
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1 1251112-003093 M6×45 hexagon flange face 9.8 bolt (color zinc) 2 10N.m
2 4050854-002051 ZT310-R engine left rear cover (dark gray) 1
3 1251300-057093 Non-standard nut M10×1.5
（
dacromet
）
3 65±5N.m
4 1274300-082000 ZT350
－
R Upper hanging piece (outside association) 2
5 1251100-060000 Non-standard bolt M10×1.5×90 4
6 1251112-023000
GB5787 Non-standard bolt M12×1.25×95 (10.9/Dacromet)
1
7 1251112-019000 Non-standard boltM12×85(10.9
级
/dacromet)
3
8 4024300-001000 ZT350
－
GK bracket 1
9 1250305-009091 GB6187.1 M12×1.25
（
White zinc
）
4
10 1251300-067000 ZT250
－
R Rear wheel hollow shaft nut
1
11 1252200-040000 ZT310-R Lrear flat fork hollow shaft Φ20×315 1
12 1251100-262000 Non-standard bolt M12×1.25×127
（
dacromet
）
1
Fig.1 FRAME & ENGINE
COMBINATION
Engine combination
PROCEDURE:
Remove bumper assembly rear,re insert the bolt connecting the guard bar with the hanger and bracket.
●
Engine left rear cover
Using 8# sleeve remove the bolt
⑴
disassemble the rear cover
⑵
.
●
The middle part of the engine is connected with the frame and the rear fork
Using 14# sleeve fix the head of the bolt
⑸
at the upper hanging piece, and using 14# plum wrench remove the nut
⑶
.
Only disassemble the nut and other parts cannot be disassembled.First Using 14# sleeve fix the head of the bolt
⑺
at the
bracket
⑻
, then using 17# plum wrench remove the nut
⑼
.Using 14# sleeve fix the head of the bolt
⑿
at the lower part of
the engine , and using 17# plum wrench remove the nut
⒀
. Don't remove the bolts
⑸、⑺、⑿、
Upper hanging piece
⑷
.
●
Disassemble the engine
First using 24# open ended spanner fix the head of the rear fork shaft
⑾
, and using 30# plum wrench remove the nut
⑽
.One person shakes the rear fork assembly slightly and one pulls the rear fork shaft
⑾
to "A" .Both of them hold the
engine left and right crankcase at the same time; one person disassembles the bolts
⑸
, take out the hanging piece
⑷
.Disassemble the bolts
⑹
and
⑺
and brackets
⑻
above the front bracket.Finally remove the bolt
⑿
at the lower part of the
engine. Hold the engine to move to one side and pay attention to safety during the movement. Place the engine smoothly on
the ground.
CAUTION
：
●
It is necessary to remove the seat cushion, fuel tank, side cover, pedal support, wind deflector,lower shroud
component,shift lever, muffler, radiator and pipe, cable, air filter joint, chain, engine negative pole, etc.
●
The coolant should be drained before disassembly.
●
The waste oil needs to be collected and returned to qualified institutions. It is forbidden to dump and pollute the
environment and the source of water.
●
All standard parts must meet the standard torque value when reassembling, and refill the engine oil according to the
operation instruction.