ZF CruiseCommand 785CE Скачать руководство пользователя страница 37

Страница: 37 / 160

SET-UP PROCEDURES

Page 29

6.1.4 Left and Right Arrow

Depress and Hold simultaneously

. (Refer to Figure 27:)

• Activates Set-up Mode. When Display Function Code begins to blink

the Push Buttons may be released.

• Saves Value and deactivates Set-up Mode. When the Display Function

Code stops blinking the Push Buttons may be released. The system is
now out of Set-up Mode and in the Function Menu.

6.1.5 Left Arrow

Depress Once. Refer to Figure 28:

• Escape from Set-up Mode without any change being stored. The Func-

tion Code will quit blinking and the previously saved values will be
restored.

• When in Function Menu, displays Error Codes, if any are presently

stored.

6.1.6 Right Arrow

Depress and Hold. Refer to Figure 29:

• Clears the Error Code from the Display, if the error had been already

resolved. Must release and then depress again to clear multiple errors.

Figure 27: Left and Right Arrow Push Buttons

Figure 28: Left Arrow Push Button

Figure 29: Right Arrow Push Button

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды