ZF CruiseCommand 785CE Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 160

background image

INSTALLATION

Page 22

5.3.1 Mounting

400 Series Control Head:

A) Use the template supplied in Appendix A.1 and drill the screw

holes and the corner cutout holes.

B) Saw between the corner cutout holes.
C) Check that the four mounting screws will start into the Control

Head.

D) Remove the Control Head.
E) Strip the adhesive cover from the gasket and apply the adhesive

side to the console.

F) See Section 5.3.2 for cable connection at the Control Head.

700 Series Control Head:

A) Refer to Appendix A.1 Control Head Variations Sheet for hole

dimensions.

B) Drill the screw holes and the cable holes.
C) See Section 5.3.2 for cable connection at the Control Head.

MC2000 Series Control Head:

A) Use the template supplied in Appendix A.1 and drill the screw

holes and the corner cutout holes.

B) Saw between the corner cutout holes.
C) Check that the two mounting screws will start into the Control

Head.

D) See Section 5.3.2 for cable connection at the Control Head.

512 Series Control Head Assembly:

A) Refer to MM14334 Installation Manual supplied with the 512 Con-

trol Head Assembly.

5.3.2 Cable Connection

The 400, MC2000, 700 or 512 Style Controls Heads may be used with the

CruiseCommand System. However, the 7-conductor wiring will require a
modification to the Control Head connections of the terminal connected
Control Heads only.

This 7-conductor cable connects the Control Head to the Processor

through an 8 Pin Plug on the Processor end of the cable. In addition to the
7-conductors, the shield wire must also terminate within the CruiseCom-
mand Processor. In order to accommodate these 8 connections, a modifi-
cation to the Control Head wiring must be done:

«
...
28
29
30
31
32
...
»

Содержание CruiseCommand 785CE

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CruiseCommand 785CE

Бренд: D-Link Страницы: 12

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: Ruckus Wireless Страницы: 56

Бренд: Renesas Страницы: 6

Бренд: Hama Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: ICP DAS USA Страницы: 62

dspstak 21262sx

Бренд: Danville Signal Processing Страницы: 35

Бренд: Tandy Страницы: 24

Бренд: Renesas Страницы: 76

Бренд: National Instruments Страницы: 80

Бренд: Advantech Страницы: 108

Бренд: ZiLOG Страницы: 317

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: AMD Страницы: 27

Бренд: EXAGATE Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды