ZF CruiseCommand 785CE Скачать руководство пользователя страница 36

Страница: 36 / 160

SET-UP PROCEDURES

Page 28

• The second two digit pads indicate the numeric Value that is currently

programmed into the Processor for that particular Function.

A decimal indicator is located on the bottom right corner of each pad.

(Refer to Figure 24:)

6.1.2 Processor Arrow Push Buttons

The Processor has four Push Buttons with arrows located below the Dis-

play. These push buttons are used to scroll through, select, and store the
Functions and Values. Refer to Figure 25:

6.1.3 Up and Down Arrow

Depress either Once. (Refer to Figure 26:)

• Stops Display Normal Operating running center red dash lines and

activates Function Menu.

• When in the Function Menu, scrolls the Function type one at a time.
• When in Set-up, scrolls one Value’s number one at a time.
• When Error Code is displayed, scrolls through the error messages one

at a time.

Figure 24: Display Pad Definitions

Figure 25: Processor Arrow Push Buttons

Figure 26: Up and Down Arrow Push Buttons

Decimal Indicators

Arrow Keys

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды