ZF CruiseCommand 785CE Скачать руководство пользователя страница 13

Страница: 13 / 160

OPERATION

Page 5

2.6 W

ARM

ODE

This feature allows the operator to increase the engine’s RPM while

the Clutch remains in Neutral. Warm-up Mode is operational only in
Ahead. The system is placed into Warm-up Mode as follows:

C) After one second move the Control Head lever to the Ahead

detent position.

D)Now release the transfer button.

• The red indicator light will blink slowly indicating Warm-up

Mode and the clutch has stayed in Neutral.

E) The operator can now start and warm-up the engine while mov-

ing the Control Head lever through the Ahead throttle ranges.

F) When the Control Head lever is returned to the Neutral detent,

the red LED will discontinue blinking and the CruiseCommand
will automatically reset to Normal Operating Mode after one
second.

G)The next Control Head lever movement will shift the transmis-

sion.

A)At the Station-in-Command,

ensure that the Control Head lever
is in the Neutral detent position
(refer to Figure 4:):

B)Depress and hold the transfer but-

ton.

Figure 4: Control Head Warm-up Mode

Figure 5: Control Head Normal Operating Mode

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды