ZF CruiseCommand 785CE Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 160

background image

INSTALLATION

Page 26

• One for the Astern Clutch solenoid
• One for Clutch Power

A) Insert the Harness plug into the CLUTCH plug-in on the Processor

Cover.

B) Run the two cables labeled Ahead and Astern Clutch to the transmis-

sion.

C) Refer to the Transmission documentation for termination points at the

clutch solenoids.

D) Run the one cable labeled

Power

to the Clutch Power Supply. Con-

nect to the Power Supply.

5.6.2 Clutch and Troll Control

The Clutch/Troll Harness is supplied with 3 or more of the following

Cables extending from the plug.

• One for the Troll Command solenoid
• One for the Troll ON/OFF solenoid
• One for Neutral Clutch solenoid
• One for Ahead Clutch solenoid (refer to Section 5.6.1)
• One for the Astern Clutch solenoid (refer to Section 5.6.1)
• One for Clutch Power (refer to Section 5.6.1)

A) Insert the Harness plug into the CLUTCH connector on the Processor.
B) Run the two cables labeled Troll Command and Troll ON/OFF to the

transmission.

C) Refer to the Transmission documentation for termination points at the

Troll solenoids.

D) Run the three cables labeled Ahead, Neutral, and Astern Clutch to the

transmission.

5.7 E

NGINE

S

TOP

S

WITCH

The Installer supplies the Stop Switches. Refer to the information sup-

plied with the Stop Switches for installation.

WARNING: Each Station must have some method to stop the engine, refer to CFR 46, SEC. 62.35-5

and ABYC P-24.5.8.

«
...
32
33
34
35
36
...
»

Содержание CruiseCommand 785CE

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CruiseCommand 785CE

tBOX330-870-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Funkwerk Страницы: 2

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

Бренд: FONESTAR Страницы: 8

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренд: Active Communications Страницы: 10

Бренд: Vega Страницы: 12

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Бренд: Disc Makers Страницы: 12

Бренд: LevelOne Страницы: 10

Бренд: SET Страницы: 38

Бренд: Agilent Technologies Страницы: 458

Бренд: Spectrum Digital Страницы: 11

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...

Бренд: 3Com Страницы: 6

Бренд: Acnodes Страницы: 10

EdgeSafe M40G1AC

Бренд: Garland Страницы: 159

Бренд: OWC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды