ZF CruiseCommand 785CE Скачать руководство пользователя страница 33

Страница: 33 / 160

INSTALLATION

Page 25

5.4.1 Tachometer Sensor Wire Harness (Active Synchronization Only)

(Multi Screw)

This Harness will be plugged on both ends of the cable. The plug on the

Sensor side is designed to mate with the ZF Mathers supplied Tachometer
Assemblies.

A) Remove from the Processor the PULSE connector cap and discard.
B) Insert the Tachometer Sensor Wire Harness plug into the PULSE

connector on the Processor.

C) Run the Port Tachometer Sensor Cable to the Port engine pulse

transmitter.

D) Run the Starboard Tachometer Sensor Cable to the Starboard

engine pulse transmitter.

E) Make cable connections at the tachometer as indicated by the

Engine Manufacturer’s documentation.

5.5 M

AIN

NGINE

PEED

ONTROL

- T

HROTTLE

ARNESS

The Processor(s) connects directly to the engine interface using a

Throttle Wire Harness.

Refer to Appendix A.1 - Parts List to select the correct Throttle Wire

Harness for the engine signal required.

A)Connect the plug end of the Throttle Wire Harness into the

THROTTLE connector at the Processor.

B) Run the cable to the engine interface.
C) Refer to the engine documentation for termination points at the

engine interface.

5.6 C

LUTCH

AND

ROLL

[

OPTIONAL

] C

ONTROL

These Harnesses will be plugged on the Processor end of the cable

only. Refer to Appendix A.1 - Parts List for the correct Harness for
this application. Refer only to the Sections that apply to the Harness
being used in this application.

5.6.1 Clutch Control Only

The Clutch Harness is supplied with 3 Cables extending from the plug.

• One for Ahead Clutch solenoid

NOTE: Ensure all Processors are set-up using the same Wire Harness and Set-up Engine Selection.

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды