ZF CruiseCommand 785CE Скачать руководство пользователя страница 142

Страница: 142 / 160

TROUBLESHOOTING

TRAIN-158 Rev.A 5/01

Page 45

G)Return the Control Head lever to the Neutral/Idle position and

turn power ‘Off’ to the Processor.

H)Remove the Test Unit and plug the Clutch Harness back into the

Processor’s Socket.

3.3 N

EUTRAL

OLENOID

ESTING

A)Ensure power is removed from both the CruiseCommand Proces-

sor and the Clutch Power Supply.

B)Disconnect the Clutch Harness from the Processor’s Clutch

Socket.

C)Insert the Test Unit between the Processor’s Clutch Socket and the

Clutch Harness as shown in Figure 40:.

D)Set-up the Multi meter to measure DC Volts and connect as shown

in Figure 40:.

E) Turn power ‘On’ to the Processor and Clutch Power Supply and

take command at any Station.

F) The measurement should be 12 or 24 VDC, depending on the

Solenoid’s rating, at this time.

G)Position the Control Head lever to the Ahead detent. The mea-

surement should drop to 0 VDC.

Figure 40: Dwg 11653-L

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды