ZF CruiseCommand 785CE Скачать руководство пользователя страница 59

Страница: 59 / 160

ADJUSTMENTS AND TESTS [AT DOCK]

Page 51

7.8 E4 - T

HROTTLE

AXIMUM

STERN

This value determines the percentage of Throttle Maximum that is
allowed in Astern. This is adjustable anywhere between 1 to 100%.

The values of this Function are 1.0% to 100.0%. Throttle defaults
are based on Throttle Profile selected.

A)Disconnect the Throttle Wire Harness from the CruiseCom-

mand Processor.

B) Connect the 8-Pin connector of the Service Field Test Unit to

the Processor Throttle connector and to the Throttle Wire Har-
ness. Refer to Figure 49:

C) Turn ON power to the Engine’s ECM. Ensure Power is On to

the Processor.

D)Depress either the Up or Down Arrow to activate the Function

Menu.

E) Use the Up or Down arrow to scroll to the

Function Code.

• The Multi Meter will read the output signal for Throttle Max-

imum Astern.

F) Activate Set-up Mode. Refer to Section 6.2.
G)Change the Value of the Function.
H)When the value required is displayed, store the value. Refer to

Section 6.2.

I) Remove the Service Field Test Unit and reconnect the Throttle

Wire Harness to the Processor.

Figure 53: E4 - Throttle Maximum Astern Set-up Activated

NOTE: To read current, the mA Push Button on the Service Field Test Unit must be depressed.

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды