Zero 88 jester 24 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 73

background image

JesterML Operating Manual

MIDI Control

52 of 73

73-406-00 Issue 2.0

Velocity Sensing

Some keyboards have this function.  It enables the musician to control the loudness
of  the  music  by  playing  notes  and  chords  delicately  for  soft  music  or  hard  for  loud
music.  The MIDI signal that is transmitted by such instruments consists of a Velocity
in the range 0 to 127.
If  the  instrument  does  not  have  Velocity  sensing,  the  Velocity  is  fixed  by  the
manufacturer, often at 63 rather than 127 so that the music that is being played is not
too loud.

/p18/3

Summary

MIDI instruments send a stream of signals from their ‘OUT’ port. The signals sent
principally consist of Note On and Note Off messages which consist of Note Numbers
and Velocities.
There may be the occasional Program Change signal if the voice is changed.

MIDI and the JesterML

The JesterML is designed only to receive MIDI information.  It cannot transmit MIDI
information  to  another  device,  although  a  ‘THRU’  port  is  provided  to  allow  daisy
chaining.

MIDI Received

In Preset mode:

The first note of any octave will drive channel 1, the second note of any octave will
drive  channel  2  and  so  on.    The  Receiving  Channel  is  set  to  <-->  by  default.    This
means that the desk will accept commands on any of the 16 channels.   The velocity
information is used to determine the fade rate of a channel.

In Run mode:

The first note of any octave will drive submaster 1, the second note of any octave will
drive submaster 2 and so on.  The velocity information is used to determine the fade
rate of the submaster.

You  can  disable  MIDI  control  completely  by  setting  MIDI  to  <Disabled>  in  Setup.
This is the default value, so if MIDI does not function, check it is Enabled first.

«
...
50
51
52
53
54
...
»

Содержание jester 24










































































Отзывы:

Нет отзывов

Похожие инструкции для jester 24

Бренд: Baker Instrument Company Страницы: 24

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: GALBIATI Страницы: 20

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: HABYS Страницы: 16

Бренд: Taurus Страницы: 24

Бренд: Jasco Страницы: 2

Бренд: quadient Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды