Zero 88 jester 24 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 73

background image

Run Mode

JesterML Operating Manual

73-406-00 Issue 2.0

29 of 73

2. Press CHASES, and then move the middle wheel to set the desired speed. If you

wish to adjust only the chase speed of the selected memory (as opposed to all
active chases), ensure you hold down SHIFT whilst adjusting the speed.

Beat Setting

Sometimes it is desirable to set a chase to match the beat of music.  To do this, firstly
you need to set the Flash Mode to Beat.  Press SPECIAL, and select the Beat option
on the Multi-Function-Keys.  Once this is done, press the INSERT button twice (once
on each down-beat of the music) to override the speed of the chase running on the
memory stack.
If a chase is running on a submaster and you wish to set a beat, set the Flash Mode
to  Beat  then  use  the  channel  flash  button  under  the  required  submaster  to  set  the
beat.  You can also press PAGE B and use the Multi-Function-Keys for this purpose.
The JesterML measures the time between one button press and the next, and takes
that as the time for the chase, until another option is defined.

Using Sound Input

A chase can be advanced in time with the bass beat of a music source, or the basic
speed of the chase can be set and the bass beat from the music source used to
increment extra steps.
1. Connect a suitable music source to the audio input on the desk. You may find it

useful to use a graphic-equaliser in line with the audio signal to optimise the
response for the particular music source being used.

2. Ensure that the sound function is active. See the Setup section of this manual for

more information on activating the sound function.

3. To use only the sound to trigger the chase, press CHASES and ensure that the

speed is set to Manual.

4. To use a combination of sound and automatic, press CHASES and set the basic

speed using the middle wheel.

NOTES

Insert Button

The INSERT button is active at all times while a chase is running.  It can be used to
advance the chase running on the memory stack by one step.  To advance a manual
chase  on  a  submaster,  use  the  submaster  flash  button,  with  the  Flash  Mode  (set
using  the  Multi-Function-Keys  when  SPECIAL  is  active)  set  to  Go.    You  can  also
press PAGE B and use the Multi-Function-Keys for this purpose.

Sound Input

If an external sound source attached to the desk is used to advance a chase, the
sound function must be activated. This is done in Setup.

Removing Sound Input

If the external sound source is removed, the chase will advance at the original rate
set by the speed setting when CHASES is selected. If this was set to Manual, the
chase will stop.

Attack

The JesterML allows you to have several different types of chase.

«
...
27
28
29
30
31
...
»

Содержание jester 24










































































Отзывы:

Нет отзывов

Похожие инструкции для jester 24

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: NEILPRYDE Страницы: 53

Бренд: 3Disc Страницы: 12

Бренд: Dana Design Страницы: 20

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: B-K lighting Страницы: 2

Бренд: Masterclock Страницы: 19

mocon AQUATRAN 3/38

Бренд: Ametek Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды