Zero 88 jester 24 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 73

background image

Glossary

JesterML Operating Manual

73-406-00 Issue 2.0

57 of 73

Direction

The order in which chase steps are output. This can be forward, backward, bounce
or random – set when CHASES is selected.

DMX512-A

Standard communications protocol for dimmers and moving lights.  512 channels of
control  are  digitally  multiplexed  and  sent  down  a  cable  to  dimmers,  which  listen  for
their  specific  data,  according  to  their  start  address.    The  official  standard  is  now
published  by  the  American  National  Standards  Institute  (ANSI)  as  E1.11-2004  –
USITT DMX512-A.  The JesterML’s DMX ports conform to this standard.

DMX In

The ability to take a DMX input (see

DMX512-A

) into the JesterML, and output it

through  the  JesterML’s  DMX  output.    This  allows  you  to  store  the  incoming  DMX
signal as part of a scene or chase.  These can then be replayed as a normal scene
or chase, but affect unpatched channels in the entire universe of DMX.

Duplicate

An additional DMX address given to a channel or a fixture.

Edit

This button loads the selected item for editing, and it will then appear on the outputs.
The  LED  in  the  button  is  then  lit.    Pressing  the  button  again  will  save  the  changes.
Alternatively  select  a  new  location  using  the  cursor  buttons,  and  press  the
PROGRAM button to save the new look there instead.

Effect

See

Movement Effect

.

Ellipse

One of a number of

Movement Effects

available on the JesterML for fixtures with

Pan & Tilt. The Movement Effect is selected using the wheels when the appropriate
POSITION wheel group is selected. By using the

Size X

&

Size Y

controls, an

ellipse can be made into a horizontal line, a vertical line or a circle.

Enter Button

The button in the middle of the cursor buttons which allows you to confirm something
on the JesterML.

Fade Down

The Fade Down time on the JesterML is the time it will take any brightness channels
fading down to crossfade to their programmed level.

Fade Up

The Fade Up time on the JesterML is the time it will take for any brightness channels
fading up to crossfade to their programmed level.

«
...
55
56
57
58
59
...
»

Содержание jester 24










































































Отзывы:

Нет отзывов

Похожие инструкции для jester 24

Бренд: Balanced Body Страницы: 4

Ettan IPGphor 3

Бренд: GE Страницы: 64

Бренд: GE Страницы: 56

Бренд: GE Страницы: 132

Бренд: GE Страницы: 16

Бренд: GE Страницы: 474

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: JB-Lighting Страницы: 40

Бренд: Olsen Страницы: 4

Бренд: Fakir Страницы: 22

Бренд: Qlight Страницы: 4

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 52

Бренд: Wayflex Страницы: 11

Бренд: Lites Страницы: 8

Бренд: Tascam Страницы: 100

Firefly Low Voltage Lighting System

Бренд: Ultra Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды