Zero 88 jester 24 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 73

background image

2 of 73

73-406-00 Issue 2.0

If a portable or temporary three phase
mains supply is used to power this
desk, we recommend that the desk
mains plug is removed before
connecting or disconnecting the
supply. Serious damage will occur if
the desk is connected across two
phases.

This equipment is designed for use as
a lighting control desk only, and is
unsuitable for any other purpose. It
should only be used by, or under the
supervision of, an appropriately
qualified or trained person.

Zero 88 reserves the right to make
changes to the equipment described in
this manual without prior notice.
E & OE.

Federal Communications Commission

This equipment has been tested and
found to comply with the limits for a
Class A digital device, pursuant to part
15 of the FCC rules. These limits are
designed to provide reasonable
protection against harmful interference
when the equipment is operated in a
commercial environment.

This equipment generates, uses, and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instruction
manual, may cause harmful
interference to radio communications.
Operation of this equipment in a
residential area is likely to cause
unacceptable interference in which
case the user will be required to correct
the interference at the operators
expense.

Issue 2.0 – May 2008

Manual Stock No. 73-406-00

© Zero 88 2007-2008

Zero 88
Usk House
Llantarnam Park
Cwmbran
Gwent NP44 3HD
United Kingdom
Tel:

+44 (0)1633 838088 *

Fax:

+44 (0)1633 867880

e-mail: [email protected]
Web:

www.zero88.com

* 24 hour answerphone

«
1
2
3
4
...
»

Содержание jester 24










































































Отзывы:

Нет отзывов

Похожие инструкции для jester 24

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

Бренд: laerdal Страницы: 9

Бренд: Yamaha Страницы: 5

Бренд: Yuwell Страницы: 2

Бренд: ABBA Страницы: 4

Бренд: Öhlins Страницы: 8

Бренд: &Tradition Страницы: 3

Flowerpot VP3 Verner Panton 1968

Бренд: &Tradition Страницы: 3

Бренд: ?HC Страницы: 2

FLOWERPOT GARDEN VP5

Бренд: &Tradition Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды