Zero 88 jester 24 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 73

background image

JesterML Operating Manual

Preset Mode

12 of 73

73-406-00 Issue 2.0

8. The operations described in steps 5 - 8 can then be repeated to set up a new

scene on the faders, crossfade to the new scene, and save it to a temporary store
etc.

Manual and Timed Crossfades

Crossfading between the scene set up on the PRESETS and the stored scene is
achieved  by  moving  the  A  MASTER  and  B MASTER faders  in  tandem.    If  the fade
time set when SPECIAL is selected is set to Snap, the crossfade time is determined
by the speed at which the A MASTER and B MASTER faders are moved.  You have
direct control over the speed of the crossfade.
The  crossfade  time  can  be  changed  from  0.1  seconds  and  5  minutes  using  the
middle wheel when SPECIAL is selected.

Flashing Channels - Wide mode

1. Ensure that the Flash function is active – this is set using the Multi-Function-Keys

when SPECIAL is selected.

2. Press and hold an individual CHANNEL FLASH button. The buttons below the

PRESET A faders control the first half of the channels, those below the PRESET
B faders control the second half of the channels. The corresponding channel is
then added to the scene at the level set on the GRAND MASTER. Dependant on
the flash mode, the other channels may or may not be affected – see below.

3. Release the CHANNEL FLASH button. All channels return to their previous level.

FLASH:

The selected channels will be sent to full when the button is pressed, and

will be returned to its fader level when the button is released. No other channels are
affected.

SOLO:

The selected channels will be sent to full and all other brightness channels

will be sent to blackout. When the button is released, all brightness channels are
returned to their normal levels.

NOTES

Stored Scene

Any stored scene being output in PRESET Mode will be removed from the outputs if
the desk is changed to PROGRAM, RUN or SETUP Modes.

Flash buttons on a wing

The flash mode not apply to FLASH buttons on a wing.

«
...
10
11
12
13
14
...
»

Содержание jester 24










































































Отзывы:

Нет отзывов

Похожие инструкции для jester 24

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: Facnor Страницы: 33

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренд: laguna Страницы: 16

Бренд: Lafayette Страницы: 2

Бренд: olympia electronics Страницы: 4

Бренд: PASCO Страницы: 5

Бренд: Pasco Scientific Страницы: 27

Бренд: PARUS Страницы: 6

Бренд: Vahterus Страницы: 31

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды