YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 52

Страница: 52 / 190

Insert the terminal tips into the terminal block as shown in the figure. The connector numbers

and power polarities are listed below.

Terminal No.

Signal

Positive

Protective ground

Negative

Terminal block

Positive

Negative

GND

Tip with a small diameter

Tip with a large diameter

Replace the attachment screws with the supplied long screws as necessary. You can remove

the attachment screws by pulling the screws in the direction of the arrow.

Attach the cable to the connector. Set the chip mount flange and cable cover flange in the

connector case grooves. Secure the cable in place using the cable retainer.

Attachment

screw

Supplied screw

Put the connector case on and fasten it with screws.

Connecting to the Power Supply

Connect the power cord as shown in the figure below. The power supply must meet the following
conditions:

Item

Description

Rated supply voltage

12 VDC

Permitted supply voltage range

10 to 18 VDC (at the DL850V connector end)

Maximum power consumption

Approx. 150 VA Max.

(135 VA when driving 16 channels with four High-Speed 100 MS/s, 12-Bit

Isolation Modules and four High-Speed 10 MS/s 12-Bit Isolation Modules)

Connect to protective

earth ground

Positive

Negative

protective earth

ground( )

Battery

DC power connector

Note

• If both AC power and DC power are supplied, AC power takes precedence.
• If both AC power and DC power are supplied and AC power is cut off, the power instantaneously switches

to DC power.

3.4 Connecting to a Power Supply and Turning the Power Switch On and Off

3-11

IM DL850-03EN

Making Preparations for Measurements

App

Index

Содержание DL850 ScopeCorder































































































































































































Результаты поиска

Содержание DL850 ScopeCorder

Отзывы:

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 52 / 190

Результаты поиска

Содержание DL850 ScopeCorder

Отзывы: