YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 129

Страница: 129 / 190

6-21

IM DL850-03EN

Specifications

App

Index

High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module (701251)

Specifications

Item

Specifications

Standard operating conditions

Temperature:

Humidity:

23 ±5°C

20 to 80% RH

After a 30-minute warm-up and after calibration

Effective measurement range

20 div (±10 div around 0 V, display range: 10 div, when Variable is OFF)

Number of input channels

Input coupling

AC, DC, and GND

Maximum sample rate

1 MS/s

Input format

Isolated unbalanced

Frequency characteristics

(−3 dB point when a sine wave of

amplitude ±3 div is applied)

5 mV/div to 20 V/div:

2 mV/div and 1mV/div:

DC to 300 kHz

DC to 200 kHz

Voltage-axis sensitivity setting

1 mV/div to 20 V/div (1-2-5 steps) (when using 1:1 probe attenuation)

Maximum input voltage

(at a frequency of 1 kHz or less)

Combined with the 700929(10:1) or 701947(100:1):

Combined with the 701954 (1:1):

Direct input (cable that does not comply with the safety standards):

600 V (DC+ACpeak)

140 V (DC+ACpeak)

42 V (DC+ACpeak)

Maximum allowable common

mode voltage

(at a frequency of 1 kHz or less)

Working voltage of safety standard

Combined with the 700929 (10:1) or 701947 (100:1)

or combined with the 701954

(1:1):

400 Vrms (measurement category Other (O)), 300 Vrms (CAT II)

Direct input (cable that does not comply with the safety standards):

42 V (DC+ACpeak) (CAT II, 30 Vrms)

Vertical (voltage) axis accuracy

DC accuracy

5 mV/div to 20 V/div:

2 mV/div:

1 mV/div:

±(0.25% of 10 div)

±(0.3% of 10 div)

±(0.5% of 10 div)

Input connector

BNC connector (isolated type)

Input impedance

1 MΩ ± 1%, approx. 35 pF

−3 dB point when AC coupled

low frequency attenuation point

1 Hz or less (0.1 Hz or less when using the 700929, 0.01 Hz or less when using the 701947)

Common mode rejection ratio

80 dB (50/60 Hz) or more (Typical

)

Residual noise level

(Input section shorted)

±100 µV or ±0.01 div whichever is greater (Typical

)

Withstand voltage

1500 Vrms for 1 minute (across each terminal and earth) (60 Hz)

Allowable transient surge voltage

(instantaneous)

±2100 Vpeak (across each input terminal and earth)

Insulation resistance

500 VDC, 10 MΩ or more (across each input terminal and earth)

A/D conversion resolution

16 bit (2400 LSB/div)

Temperature coefficient

Zero point:

Gain:

5 mV/div to 20 V/div:

2 mV/div:

1 mV/div:

1 mV/div to 20 V/div:

±(0.02% of 10 div)/°C(Typical

)

±(0.05% of 10 div)/°C(Typical

)

±(0.10% of 10 div)/°C(Typical

)

±(0.02% of 10 div)/°C(Typical

)

Bandwidth limit

Select from OFF, 40 kHz, 4 kHz, and 400 Hz
Cut-off characteristics:

−12 dB/OCT (Typical

)

Probe attenuation setting

Voltage probe: 1:1, 10:1, 100:1, 1000:1
Current probe: 10 A:1 V (for the 700937/701933), 100 A: 1 V (for the 701930/701931)

Compatible probes/cables

Voltage probe: Recommended

700929 (10:1 safety probe).20 to 45 pF: For measuring 600 Vpeak or less

701947 (100:1 probe).15 to 45 pF: For measuring 600 Vpeak or less

Current probe (power can be supplied from the DL850/DL850V. Option)

700937 (15 A), 701930 (150 A), 701931 (500 A), 701933 (30 A)

High voltage differential probe (connect the GND cable provided with the probe to the DL850/

DL850V case)

700924 (1000:1, 100:1/1400 Vpeak): For measuring 1400 Vpeak or less

Connection cable (for high voltage 1:1)

701901 (isolated type BNC-safety alligator clip adapter ×2: For measuring 200 Vpeak or

less), 701954 (alligator clip (dolphin type) red/black 2-piece set) is required separately

Connection cable (for low voltage 1:1)

366926 (non-isolated type BNC-alligator clip ×2: For measuring low voltage less than or

equal to 42 Vpeak)

1 Value measured under standard operating conditions.

6.13 Module Specifications

Содержание DL850 ScopeCorder































































































































































































Результаты поиска

Содержание DL850 ScopeCorder

Отзывы:

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 129 / 190

Результаты поиска

Содержание DL850 ScopeCorder

Отзывы: