manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 143 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 143

6-35

IM DL850-03EN

Specifications

1

2

3

4

5

6

App

Index

Acceleration/Voltage Module (with AAF) (701275) Specifications

Item

Specifications

Standard operating conditions

Temperature:

Humidity:

23 ±5°C

20 to 80% RH

After a 30-minute warm-up and after calibration

Effective measurement range

20 div (display range: 10 div)

Number of input channels

2

Input coupling

AC, DC, GND, ACCL (acceleration), and GND

Maximum sample rate

100 kS/s

Input format

Isolated unbalanced

Frequency characteristics

1

(−3 dB point when a sine wave 

of amplitude ±3 div is applied)

Waveform observation mode:

DC to 40 kHz

Acceleration measurement mode: 

0.4 Hz to 40 kHz

Voltage-axis sensitivity setting 

5 mV/div to 10 V/div (1-2-5 steps) (when using 1:1 probe attenuation)

Acceleration (±5 V = ×1 range): ×0.1 to ×1 to ×100 (in 1-2-5 steps)

Maximum input voltage 

(at a frequency of 1 kHz or less)

42 V (DC+Acpeak)

2

Maximum allowable common 

mode voltage 

(at a frequency of 1 kHz or less)

Working voltage of safety standard

42 V (DC+ACpeak) (CAT II, 30 Vrms)

3

Vertical (voltage) axis accuracy 

DC accuracy

1 

Waveform measurement mode DC accuracy:

±(0.25% of 10 div)

Acceleration measurement mode:

±(0.5% of 10 div) at 1 kHz

Input connector 

Metal BNC connector

Input impedance 

1 MΩ±1%, approx. 35 pF

−3 dB point when AC coupled

low frequency attenuation point

0.4 Hz or less (0.04 Hz or less when using the 701940) (Typical

4

)

Common mode rejection ratio

80 dB (50/60 Hz) or more (Typical

4

)

Residual noise level 

(Input section shorted)

±100 µV or ±0.01 div, whichever is greater (Typical

4

)

A/D conversion resolution 

16 bits (2400LSB/div)

Temperature coefficient 

When in waveform measurement mode (excluding AUTO filter)

Zero point:

Gain:

±(0.02% of 10 div)/°C (Typical

4

)

±(0.02% of 10 div)/°C (Typical

4

)

Response time (only when 

observing RMS) 

Select from OFF, Auto, 4 KHz, 400 Hz, and 40 Hz

Cutoff characteristics:

Cutoff frequency (fc) when set to AUTO

Sample rate of 100 kHz or higher:

Sample rate of 100 Hz to 50 kHz:

Sample rate of 50 Hz or less:

Cutoff characteristics when set to AUTO:

−12 dB/OCT (Typical

4

, excluding AUTO)

fc = 40 kHz

fc = 40% of the sampling rate

fc = 20 Hz

−65 dB at 2×fc (Typical

4

)

Bandwidth limit

Voltage probe

Current probe

1:1, 10:1, 100:1, or 1000:1

10 A:1 V (for the 700937/701933), 100 A:1 V (for the 701930/701931)

Probe attenuation setting 

Connection cable (for low voltage 1:1)

366926 (non-isolated type BNC-alligator clip × 2: For measuring low voltage less than or 

equal to 42 Vpeak)

Voltage probe (10:1 passive probe) 

701940 17 to 46 pF: For measuring 600 V (DC+ACpeak) or less

Current probe (power can be supplied from the DL850/DL850V)

700937 (15 A), 701930 (150 A), 701931 (500 A), 701933 (30 A)

Sensor supply current (voltage)

OFF/4 mA ± 10%(approx. 22 VDC)

Applicable acceleration  sensor

Built-in amplifier type

Kistler Instrument Corporation: Piezotron, PCB Piezotronics Incorporated: ICP, ENDEVCO

Corporation: ISOTRON, etc.

6.13  Module Specifications

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов