manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 156 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 156

6-48

IM DL850-03EN

Logic Input Module (720230) Specifications

Item

Specifications

Standard operating 

conditions

Ambient temperature: 23 ± 5°C
Ambient humidity: 20 to 80% RH

Number of input ports

2

Number of input bits

8 bits per port

Maximum sample rate

10 MS/s

Input format

Use a non-isolated, dedicated probe (automatic detection)

Compatible probes

700986 (non-isolated 8-bit input)
700987 (isolated 8-bit input)
702911 (non-isolated 8-bit input)
702912 (non-isolated 8-bit input)

Chatter suppression time 

settings

Off, 5 ms, 10 ms, 20 ms, 50 ms, and 100 ms

 

CAUTION

•  Applying a voltage greater than the limits listed below may damage the logic probe or the 

instrument. For frequencies above 1 kHz, damage may occur even if the voltage is less 
than the limits listed below.

  Maximum input voltage (at a frequency of 1 kHz or less)
  •  Logic probes 702911 and 702912: 35 V
  •  High-speed logic probe 700986: 42 V (DC + ACpeak)
  •   Isolated logic probe 700987: 250 Vrms (however, ACpeak must be less than 350 V, and 

DC must be less than 250 V)

•  For logic probes 702911, 702912, 700986, and the high-speed logic probe, the eight input 

lines of a single pod share the same ground. Also, the instrument’s ground and the grounds 
of each pod are connected. Do not apply signals with different common voltages to each 
input line. Doing so may damage the instrument, connected logic probes, and connected 
devices.

•  The input terminals of an isolated logic probe are isolated from each other and from the 

DL850/DL850V.

•  Turn off the DL850/DL850V before you connect or remove a 26-pin connector from the 

logic signal input connector.

•  Do not stack isolated logic probes. Also, to prevent a probe’s internal temperature from 

rising, provide a sufficient amount of space around it.

•  Do not use the YOKOGAWA 700985 logic probe with the DL850/DL850V. The 700985 

is shaped so that it can be connected to the logic signal input connector of the DL850/
DL850V, but it is not electrically compatible with the DL850/DL850V, so connecting the two 
could damage the DL850/DL850V or the 700985.

6.13  Module Specifications

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов